Flow Benches |
|
680 cfm @ 28" h2O
1137 cfm @ 10" h2O
(make sure you check both of these capacities before you buy a flowbench) |
$8,400.00 |
|
The J-1000 is the first completely computerized flow bench, its changes in range and of flow (Intake/exhaust) are carried out by neumatics movements. It uses AUDIE TECHNOLOGY for its system of data acquisition, motor control, valves openers and swir |
$14,300.00 |
|
The J-600 is the first completely computerized flow bench, its changes in range and of flow (Intake/exhaust) are carried out by neumatics movements. It uses AUDIE TECHNOLOGY for its system of data acquisition, motor control, valves openers and swirl |
$12,500.00 |
|
The S-600 has a 14 inch water inclined manometer (for measuring flow), and two 48 inch vertical manometers. Nine 240 volt vacuum motors give it a capacity of 600 CFM at 28 inches. |
$7,495.00 |
|
The S-400 offers high capacity and good performance. It has a 6-inch water inclined manometer (for measuring flow), and two 40 inch vertical manometers. Seven 240 volt vacuum motors give it a capacity of 400 CFM at 28 inches. |
$7,200.00 |
|
The S-250 meets the need for a more economical flowbench with good air capacity which is necessary for producing the air speeds it needs to properly test heads. Four 240 volt vacuum motors give it a capacity of 250 CFM at 28 inches. |
$4,500.00 |
|
*LOOK AT ALL PICTURES* |
$89.00 |
|
HAND HELD INSTUMENT FOR PORT MAPPING AND MEASURING VELOCITIES IN PORTS.
TUBES CONNECT YOUR AUXILLARY MANOMETER TO THE PITOT TUBE AND PRESSURE IS MEASURED |
$310.00 |
|
BY HAROLD BETTES |
$22.00 |
|
220 SINGLE PHASE |
$3,750.00 |
|
TOM VAUGHT DESIGN |
$1,750.00 |
|
The bracket is 7" long x 1.5" high. The set consists of seven balls, sizes 1/8" thru 1/2" in 1/16" increments with two flags, one straight, one bent 90ยบ. The balls are welded to 8" rods with eyes for hanging. |
$99.00 |
|
FOR MOST FEL-PRO GASKET NUMBERS |
$45.00 |
|
SBC / BBC SHOWN. CALL WITH YOUR CYLINDER DIAMETER AND BOLT PATTERN. |
$450.00 |
|
THIS IS A UNIVERSAL VALVE OPENER. |
$375.00 |
|
Harold Bettes named dealer / consultant for Jamison Equipment Saenz flowbenches.
Harold can be reached at (719)260-7129
Harolds website is www.powertechnologyconsultants.com |
$0.00 |
|
THIS FEATURE COMES STANDARD ON ALL SAENZ J-600 AND J-1000 FLOWBENCHES. |
$635.00 |
|
THIS FEATURE COMES STANDARD ON ALL J-600 AND J-1000 COMPUTERIZED FLOW BENCHES.
THIS CAN BE ADDED TO A MANUAL BENCH AND USED WITH AUDIE FLOW PRO SOFTWARE |
$860.00 |
|
BASE SENSOR PACKAGE (VERSION 2) USWED ON ALL SAENZ J-600 AND J-1000 SERIES FLOWBENCHES.
THIS CAN BE ADDED TO A MANUAL FLOWBENCH AND USED WITH FLOW PRO SOFTWARE. |
$985.00 |
|
THIS SOFTWARE IS INSTALLED ON ALL J-600 AND J-1000 SAENZ BENCHES.
THIS CAN ALSO BE INSTALLED ON SAENZ S-SERIES MANUAL BENCHES OR YOUR EXISTING BENCH.
FOR A DEMO OF THIS SOFTWARE GO TO: http://www.audietech.com/ |
$260.00 |
| |
Showing Products 1 - 20 of 21 Total
Next »
|
